FRIDGE DEFROSTING AND REPAIR IN NAIROBI KENYA
Your refrigerator is arguably one of the most important appliances in your home – after all, it keeps your food from spoiling, saving you from many trips to the grocery store. However, refrigerators are not indestructible. They suffer from daily wear-and-tear just like other home appliances. While some problems are more serious than others, many can be solved by a quick fix without the help of a refrigerator repair technician. However, before you can fix the problem, it is important that you pinpoint its source.
Pay attention to the symptoms exhibited by your refrigerator in order to find the source of the problem. Then refer to our guide below on quick fixes that don’t require you to call a professional or purchase a new fridge entirely. It may just be a case of simply unplugging and re-plugging or purchasing some replacement parts.
Water Leaking on the Floor
Not only is this problem dangerous to people who are walking around your kitchen, but it is also a little bit tricky to solve as it can be caused by a couple of things. Luckily, the two most common causes have a quick and easy fix that usually don’t require the help of a professional.
One cause of water leaking onto the floor is a blocked de-frost drain. The defrost drain is typically located on the back wall of the freezer, right above the slope from the floor to the back. A buildup in food particles or debris can clog the drain hose, leading to ice buildup and water leaking out of the freezer and fridge. To fix this, try draining the hole from the inside using warm water. Use a long, slender instrument such as a pipe cleaner or turkey baster to remove the clog.
If this doesn’t get the job done, you might have to manually remove the buildup that is clogging the valve at the end of the drain hose. Locate the defrost drain hose in the back of the service panel by pulling your fridge away from the wall. This hose should have a rubber valve that helps catch debris and prevent clogging. Wash the valve with hot water and soap then reinstall.
A clogged or frozen water supply can also cause water to leak on the floor and puddle under your fridge. This can also prevent the icemaker and water dispense from working properly. In order to fix this, unplug the refrigerator and locate the shut-off valve. This could be located underneath your sink, behind the fridge, or below the fridge in a basement or crawl space. Once you locate it, make sure the shut-off valve is closed and check for any problems in the plastic supply line. If it is broken or torn, you need to replace the water supply line.
If your water line is damaged, you can still use your refrigerator to keep your food cold, you just won’t be able to use the ice or water dispenser.
Freezer Isn’t Cold Enough
Is your perishable food spoiling quickly or are you just noticing that your freezer isn’t as frosty as it should be? This is a common problem that is usually an easy fix. If you notice this problem in your freezer unit, check if the back wall of the freezer is cold.
If it is cold, check if you can hear the evaporator fan running or if you can feel air flowing from the freezer vents. If you can’t then it is most likely a problem concerning the freezer evaporator fan. If you can feel the air flowing and hear the fan running, you should check on the refrigerator’s compressor. Clean any dust that could be preventing air from moving across the coils. These are condenser coils that release heat from inside the fridge into the room. If your condenser coils are clean, it may be time to invest in that spiffy French door refrigerator you’ve had your eye on.
Unit is cycling too often
Nobody likes a noisy fridge. Not only is it inconvenient because of the constant noise, but it can also cause your energy bill to run high, taking quite the toll on your wallet. There are a few things that can cause your fridge unit to cycle too often – one being a buildup of debris or dust around the condenser coils.
To fix this, you want to begin by unplugging your fridge. The condenser coils are usually located on the very bottom of your fridge and can be accessed from the front or the back. To find the condenser coils, first locate the “grill” and remove it by popping out the snaps that hold it in place. After doing this, use a small vacuum to remove the buildup of dust or debris around the condenser coils. You may even need to use a cloth to remove any buildup in those hard-to-access places. Once all of the debris and dust is removed, put the grill back on and plug the refrigerator back in. Problem solved!
Another common cause of your refrigerator unit cycling too often is setting the temperature too low. Not only will this cause some of your food to spoil, but it also results in the refrigerator working overtime. A good rule of thumb is to set your fridge temperature at or below 40 degrees Fahrenheit. Make sure that you are checking the thermostat on your refrigerator from time to time to ensure that it is running at the correct temperature. If this doesn’t resolve the problem, it may be time to call in a repair technician as it might be the case of a defective part such as a condenser fan motor or thermostat sensor.
Fresh Food Compartment Is Warming Up
Before we can discuss the solution to this problem, it is important to understand the connection between your refrigerator and your freezer unit. Typically, the cold air generated by refrigerators comes from the freezer unit, which then flows into the fresh food section of your fridge. Therefore, if your fresh food compartment is warming up, it is most likely because you have an airflow problem.
Your freezer contains an evaporator fan that is responsible for moving the cold air from the freezer into the fresh food compartment in the fridge. This air moves through a diffuser, which is located in the back of the fresh food section of your fridge. If you can hear the evaporator fan running or can feel air blowing from the freezer vents and are still facing an issue, your diffuser duct may be clogged with ice. This is preventing air from passing through and is oftentimes caused by the door being left open for a long period of time.
However, if you can’t hear the evaporator fan running or hear an uncommon humming noise, you most likely need to invest in a new motor for your evaporator fan.
Sheet of Ice on the Freezer Floor
If you notice that there is a sheet of ice on the floor of your freezer or any water dripping into the fridge every once in awhile, it is probably an issue of a blocked defrost drain. This is usually a quick and easy fix. Simply store your food somewhere else for the time being, unplug the fridge, and allow it to defrost. This should usually resolve the issue.
However, if you want to be extra thorough, carefully remove the back wall of the freezer compartment before you plug the unit back in. Check for and remove any food or particles that are clogging the small hole at the base of the evaporator coils. If the problem remains, consider adding a drain heater to help the defrost process.
Buildup of Frost in the Ice Dispenser
This is a very common problem and a relatively simple fix! In order for ice to fall from your ice dispenser, it needs to be able to open and close. This “door” that opens and closes allowing ice to fall is called a damper door. Your damper door is lined with a special material that seals against the ice shoot and create an airtight seal. If this material on the door gets malformed or dirty, it might not be able to seal tightly, allowing moist air to enter into the freezer compartment. When this air cools down, it turns into frost causing airflow issues and cooling problems. Therefore, if you encounter this problem, simply inspect the damper door for anything that may be causing air to leak through. It may be a case of simply cleaning up the dirt or you may need to buy a replacement part.
Ice Maker is overflowing
This is a relatively common problem with a variety of potential causes. The primary problem usually is the water inlet valve. If the water pressure in this valve is too low, it may not fully close when the power is shut off. This will result in the valve leaking water into the icemaker, causing the ice maker to overflow. To resolve this issue, ensure that the water pressure is at least 20 psi. If you check and the water pressure is appropriate, you may have a defective water inlet valve. It may not be shutting off completely or may be stuck open causing water to leak through the valve. Therefore, if the ice maker is still overflowing at a sufficient water pressure, consider replacing the water inlet valve.
Refrigerator is Freezing Food
If you notice that your refrigerator is freezing your food, it is most likely a problem with the temperature control thermostat. This thermostat controls the voltage to the compressor and evaporator fan motor; therefore, if it isn’t working correctly, it might cause the refrigerator system to run longer than necessary, causing the unit to be too cold.
Determine if the thermostat is faulty by rotating it from the lowest setting to the highest setting, listening for a click. If you hear a click, rest assured that it is likely not defective. However, if you don’t hear a click, use a multi-meter to test the thermostat for continuity. If it doesn’t have continuity at any setting, replace the thermostat.
Water Dispenser Not Working
There are three possible sources that may stop your water dispenser from working.
The first, and most common reason is that your water tube in the door is frozen. To determine if this is the source of the problem, disconnect the tube at the bottom of the door and blow air through it. If the air doesn’t pass through, it is a telltale sign that your water supply tube is frozen. To fix this, simply thaw it out. To prevent this from happening again, make sure to periodically check that your freezer is set at the proper temperature. It should be set somewhere between 0 to 10 degrees Fahrenheit. If it is any lower than this, the water line could freeze.
Another possible cause for this issue is a faulty water inlet valve. This valve opens the water supply to the dispenser; therefore, if the valve is defective or if the water pressure is too low, the water valve won’t open. Before jumping to conclusions and buying a replacement part, check if the water pressure to the valve is at least 20 psi.
If your home has insufficient water pressure, it may result in your water dispenser not working. Because the water inlet valve requires a minimum of 20 psi to function properly, this may be the cause of your problem. Check the water flow from your house supply to determine if the water pressure is at least 20 psi.
Your fridge is one of the most important appliances in your home. Knowing what symptoms to look out for and understanding how to fix them can be save you a lot of time and money. If you encounter any of these problems and are unable to fix them, call a repair technician for assistance. If they tell you that it might be time to invest in a new refrigerator, we hope you turn to Best Appliance Repairs. We carry a wide selection of side-by-side refrigerators, French door refrigerators, stainless steel refrigerators, and counter-depth refrigerators at affordable prices.
So you’ve just taken delivery of a new refrigerator. Congratulations! Now it’s time to install it in the nicest spot of your kitchen, ready for all those admiring glances and chilly vegetables. Installing it yourself isn’t hard to do: just follow these simple steps and you’ll be up and refrigerating in no time.
Unpack the fridge outside
The huge cardboard boxes that the fridge was shipped in is easier to open outside, where you have room. Remove the cardboard box and other packing parts and set them aside. Don’t throw them out until the refrigerator has been up and running for a few days, though, in case you need to return it for replacement or repair.
Inside the refrigerator, remove all of the shelves, drawers and other components and set them aside so they don’t get damaged while installing. However, leave the plastic covering on the refrigerator doors in place: this can protect them from damage as you move them.
Move the refrigerator
To move a refrigerator, the easiest way is to use a dolly or hand truck, tilting the refrigerator on one side so the weight is balanced on one side. Never put a refrigerator on its side or upside down: this can weaken or damage the cooling mechanism inside. If you need to carry it up stairs, keep it as upright as possible and move carefully to avoid knocking it.
Take the doors off
Larger refrigerators are especially difficult to move, because they often won’t fit through the doorways in your house. There is a hidden trick here, though: all refrigerators are designed to have removable doors. The doors are held in place by bolts at the top and bottom, and can be removed by undoing them. Check the manual for details on this, though: some may require that you remove the bolts in a particular order, or remove other parts (such as water feeder lines) first.
Once the door (or doors) are removed, the refrigerator will be much thinner and easier to move into the kitchen. Once it is installed, you can replace the doors by reversing the sequence and you are good to go.
Mind the gap
You, of course, measured the space that the refrigerator and bought an appropriately sized one. But it never hurts to double-check: Before you move the refrigerator inside, measure the spot that it is going into, taking note of the depth, height and width. Then compare this with the measurements of the refrigerator itself and air gap that the manufacturer recommends. You’ll find this in the manual that came with the refrigerator This gap allows air to circulate, carrying away the heat that the refrigerator is removing from the food inside. The size of the required gap varies with different models and types of refrigerators, so make sure you check this and have the space you need.
How to level your refrigerator
Modern refrigerators don’t have the exposed coils that you might remember on the back of your grandparents’ fridge. These were one of the main ways that refrigerators were damaged: crack these fragile pipes, and the coolant would escape. Instead, the coils on modern refrigerators are mounted inside the body, against a metal plate on the back of the fridge. You still need to make sure that this plate has the space to radiate the heat away, though: most fridges will require a space of 2 inches or so to provide the proper air currents. If you are interested in how refrigerators work, read my article on the cool physics of refrigerators.
You should never skimp on the air gap: your refrigerator might still work if you do, but it won’t run as efficiently as it could, and you are shortening the life of the refrigerator by making it work harder to remove the heat.
You should also double-check on the space required for the door and hinge: some refrigerators will require a lot of clearance to allow you to open the door properly. Again, the details of this should be in the installation guide.
Slide it in
Once you are happy with the space that the refrigerator will go into, put it in front of the space, but with enough of a gap that you can get behind it. Sweep out the space to get rid of dust and dirt, then connect the power and water, making sure that the cables for both are against the wall so they won’t get caught as the refrigerator slides in.
Push the refrigerator in slowly, checking that it is not getting caught on any cables or flooring. Many fridges come with wheels on the back to make this easier: lift the front up gently so the front legs are off the ground and push backward gently.
Once it is in place, check the air gap on each side to make sure it is as wide as the manufacturers recommend. If not, pull it out, move it in the required direction and slide it in again.
Now you can replace the doors if required. These will need leveling to make sure that they are flat against the front of the refrigerator and form a tight seal. The method of doing this varies but usually involves adjusting a screw at the bottom of the door to level it. You should also make sure the refrigerator itself is level, as they work most efficiently this way. See this article for details on how to do this
Next, install the shelves and trays, close the doors and let the refrigerator start working. Don’t expect the fridge to become cold immediately: some refrigerators may require a few hours for the cooling system to settle down and start working after being bounced about during shipping. However, if you aren’t detecting any drop in temperature within 24 hours, call the retailer or manufacturer and ask for assistance.
WASHING MACHINE REPAIR, COOKER REPAIR, OVEN REPAIR, DISHWASHER REPAIR, DRYER REPAIR, FRIDGE REPAIR, REFRIGERATOR REPAIR, EXHAUSTER SERVICES, TELEVISION REPAIR, HOME THEATRE REPAIR, DOOR LOCKS REPAIR, ROOF REPAIR, LAWN MOWER REPAIR, COMPUTER REPAIR & MORE SERVICES WE OFFER IN NAIROBI & MOMBASA KENYA
- Fridge Repair in Nairobi & Mombasa Kenya
- Washer Repair in Nairobi & Mombasa Kenya
- Cooker Repair in Nairobi & Mombasa Kenya
- Oven Repair in Nairobi & Mombasa Kenya
- Dishwasher Repair in Nairobi & Mombasa Kenya
- DSTV Installation in Nairobi & Mombasa Kenya
- Hood Extractor Repair in Nairobi & Mombasa Kenya
- Home Theatre Repair in Nairobi & Mombasa Kenya
- Petrol & Diesel Generator Repair in Nairobi & Mombasa Kenya
- Exhauster Services in Nairobi & Mombasa Kenya
- Best Washing Machines Repair in Nairobi & Mombasa Kenya
- Best Fridge, Refrigerators & Freezers Repair in Nairobi & Mombasa Kenya
- Best Appliances Repair Facebook in Nairobi & Mombasa Kenya
- Best Appliances Repair Youtube Channel in Nairobi & Mombasa Kenya